Installation Using Splice Clips (Option 1) These instructions will assist you with installing your pizza oven belt purchased from pizzaparts.com using the supplied splice clips. Before you begin, the following tools are needed during the installation: STEP 1 – Position belt on your pizza oven as shown below. Note direction of travel. STEP 2 - If your belt is too long, it might be necessary to cut any excess belting with wire cutters. Before doing this, hold the belt together as if it were connected and check the tension of the conveyor belt to decide how many wires need to be removed. The belt should lift between 3-4' when pulled upwards. If necessary, carefully cut the wire strand(s) to remove the full width strand wire. The wire strand weaves between two rows, so be sure you are only cutting out the intended wire. STEP 3 - Once you have established a desired length, connect the provided inside master links/splice clips. When examining all splice clips, you will notice that 2 have a longer left and right side. You will use these for the edges after the center splice clip is in place. Check that the splice clips are oriented as shown below and bend them with your needle nose pliers. STEP 4 - After all splice clips/links are connected, check for freedom of movement of the conveyor belt by pulling it forward (as it will move in operation) for about 2-3 feet (60 to 90 cm) with your fingers. The conveyor must move freely. Installation Using A Full Width Strand Wire (Option 2) These instructions will assist you with installing your pizza oven belt purchased from pizzaparts.com using the supplied strand wire.
STEP 1 – Position belt on your pizza oven as shown in figure 1 and refer to the belt as Section “A” and Section “B” (Note direction of travel). STEP 2 – Carefully bend the center span of the splice wire, as shown in figure 1, trying not to distort the “Z” bends. Insert the splice wire down through the top of section “A” and up through the bottom of section “B”. STEP 3 – Pull splice wire through until belt comes together as shown in figure II STEP 4 – Locate the next “open” Z bend in section “B” and weave down through at location B1. Weave up through the next “open” Z bend in section “A” at location A1.
![Wow Oven Manual Wow Oven Manual](http://www.middleby.com/images/PS520/PS520-D.gif)
PS360G Series Gas Ovens Model: Combinations: PS360G Gas Single Oven Double Oven (Two-Stack) Triple Oven (Three-Stack) OWNER’S OPERATING AND INSTALLATION MANUAL for domestic and standard export ovens. Oven should be familiar with the function and operation of the oven. This manual must be kept in a prominent, easily reachable location near. With a manufacturer accessories and parts, you can rest assured that your oven will stay safe, efficient and covered by its warranty. Parts Town has a massive collection of Middleby Marshall manuals, so you can browse for maintenance tips, diagrams and replacement parts instantly.
STEP 5 – Continue step 4 until you have reached the edge of the belt. Using needle nose pliers, bend the edge of your splice wire down through the edge in section “A”, and up through section “B”.
NOTE – It is best to start weaving from the center of the belt and work towards one edge. Once completed, weave the other side of the belt. STEP 6 – Repeat steps 4 and 5 to complete the other side of the belt. STEP 7 – Straighten the splice strand as much as possible. NOTE – For temporary splicing, splice clips are available for all belts. When purchasing a belt from pizzaparts.com you receive splice clips and a full width strand wire with your order.
Middleby Marshall Named 2013 Kitchen Innovations Award Winner Model Bake Chamber Conveyor Width Gas/Electric Spec Sheet NEW! - PS629G WOW 29' 18' Gas NEW!
- PS629E WOW 29' 18' Electric PS360GWB WOW2 55' 38' Gas PS360G WOW2 55' 32' Gas NEW! - PS638G WOW 38' 26' Gas NEW! - PS638E WOW 38' 26' Electric PS640 40' 32' Gas PS640 Hearth Bake 40' 32' Gas PS640 40' 32' Electric PS670 70' 32' Gas Middleby Marshall. 1400 Toastmaster Drive. Elgin, IL.
60120 Oven Sales: 877-34-OVENS. Office: 847-741-3300 Email: ©2017 Middleby Marshall.
All rights reserved.